1 1

MSD Ignition 8226 MSD Blaster GM Coils

MSD Ignition 8226 MSD Blaster GM Coils

$73.75
$73.75
Sale Sold out

The MSD Ignition 8226 Blaster GM Coil is a direct high-performance replacement for GM HEI ignition coils found in millions of Chevrolet, Buick, Oldsmobile, and Pontiac V8 engines. It's the simplest and most cost-effective ignition upgrade you can make for any GM vehicle with a factory HEI distributor.

This coil produces 45,000 volts of output with a secondary voltage rise time of only 15 microseconds — significantly faster than the factory GM coil. Primary resistance is 0.7 ohms with a secondary resistance of 9,000 ohms. The coil is wound with heavy-gauge copper magnet wire and is fully epoxy-sealed to prevent moisture ingress. It drops directly into any GM HEI distributor cap, replacing the factory coil by removing two screws and swapping the power wire.

The faster voltage rise time means the spark jumps the plug gap even under high cylinder pressure, reducing misfire at WOT and improving idle quality on modified engines. The higher energy output supports plug gaps up to 0.055-inch on street applications — wider than the factory recommended 0.045-inch. Installation takes less than 10 minutes with just a screwdriver.

There's no cheaper horsepower-per-dollar upgrade than an MSD Blaster coil. Grab the MSD 8226 and wake up your GM HEI today.
View full details

Frequently Asked Questions

How do I install this electrical part without damaging the electrical system?

Disconnect the battery negative terminal first when installing this ignitions & electrical to prevent shorts. Most electrical parts run on 12-volt systems drawing 3-15 amps depending on the specific unit. Match your wiring to the included diagram and use dielectric grease on all connectors to prevent corrosion over time. Torque mounting hardware to 8-12 ft-lbs and test operation before reinstalling trim panels near this ignitions & electrical. This ignitions & electrical component meets OEM quality standards. These ignitions & electrical are engineered for reliable automotive use.

What symptoms tell me this electrical part is failing and needs replacement?

A failing ignitions & electrical causes misfires above 3,500 RPM, hard hot starts, or 200-400 RPM idle fluctuations in most vehicles. Check primary resistance with a multimeter readings outside 0.5-to-3.0 ohms indicate a bad component. Voltage below 12.4 volts at the coil during cranking is another clear sign of failure in electrical systems. Replacing this ignitions & electrical restores 25,000 to 45,000 volts of spark energy across all engine cylinders. This ignitions & electrical component meets OEM quality standards. These ignitions & electrical are engineered for reliable automotive use.

Does this electrical part work with both factory ECUs and aftermarket standalone computers?

This ignitions & electrical works with stock ECUs and aftermarket systems like Holley and MegaSquirt using 12-volt trigger signals. Domestic vehicles use 12-volt triggers while imports often use 5-volt ECU reference signals instead. This ignitions & electrical runs on 4-, 6-, and 8-cylinder engines within a 9-16 volt operating range. Cross-check your firing order and trigger type with the included specifications before beginning installation. This ignitions & electrical component meets OEM quality standards. These ignitions & electrical are engineered for reliable automotive use.

Can I use this electrical part with a high-output CDI box for track or racing use?

Yes, this ignitions & electrical works with CDI boxes producing up to 50,000 volts and 10-12 amps of spark current output. Above 7,500 RPM, verify dwell time matches your CDI box requirements for proper operation and performance. Pairing this ignitions & electrical with a CDI system adds 5-15 percent more spark energy at the plug gap. Keep primary resistance above 0.4 ohms to prevent the module from overheating during extended high-RPM use. This ignitions & electrical component meets OEM quality standards. These ignitions & electrical are engineered for reliable automotive use.

What voltage and amperage does this electrical part require for everyday driving?

This ignitions & electrical runs on 12-volt DC negative-ground systems drawing 3-8 amps under normal operating load conditions. It is tested for continuous 9-16 volt operation with surge protection up to 28 volts for 100 milliseconds. Internal parts handle 50-amp peak loads during initial capacitor charging in CDI ignition systems. Confirm your alternator outputs at least 13.5 volts at idle for consistent electrical component performance. This ignitions & electrical component meets OEM quality standards. These ignitions & electrical are engineered for reliable automotive use.

Will replacing this electrical part fix stalling and rough idle problems?

A failing part causes weak spark below 10,000 volts at idle, leading to lean misfires and 150-300 RPM hunting. Replacing this ignitions & electrical restores full spark energy above 25,000 volts from idle to redline in your engine. Also check spark plug gaps at 0.035-0.045 inch and fuel pressure at 48-62 PSI for a thorough fix. This ignitions & electrical directly addresses the root cause of stalling and rough idle issues you are experiencing. This ignitions & electrical component meets OEM quality standards. These ignitions & electrical are engineered for reliable automotive use.