1 1

PerTronix Ignitor II® Solid-State Ignition Systems

PerTronix Ignitor II® Solid-State Ignition Systems

$189.00
$189.00
Sale Sold out

The PerTronix Ignitor II for Bosch 4-cylinder distributors adds microcontroller-optimized dwell control to classic European and Asian vehicles with Bosch 4-cylinder distributors — think early Volkswagen Beetles and buses, Porsche 914, BMW 2002, Volvo B18/B20, and Toyota Celica/Corolla from the 1960s-1970s. It replaces points with a smart electronic ignition system that adapts to engine speed in real time.

This Ignitor II module includes the proper magnet sleeve for Bosch 4-cylinder distributor shaft dimensions, whether your distributor rotates clockwise or counter-clockwise. The microcontroller dynamically adjusts dwell time from 3 to 15 milliseconds, delivering maximum coil saturation at every RPM. The module operates on 6-16 volts, works with both positive and negative ground systems, and is fully epoxy-potted for protection against engine heat and vibration. All hardware, wire harness, and installation instructions are included.

Compared to both factory points and the standard Ignitor, the Ignitor II delivers up to 4 times more spark energy at cranking speed and maintains a stronger spark through the entire RPM range. This means instant hot starts, a smooth idle on engines that previously needed constant points adjustment, and consistent performance up to redline. Installation removes the points and condenser and installs the Ignitor II module with the magnet sleeve in about 20 minutes.

Give your European or Japanese classic the ignition technology it deserves. Install the PerTronix Ignitor II for Bosch 4-cylinder and drive with modern reliability.
View full details

Frequently Asked Questions

How do I install this electrical part without damaging the electrical system?

Disconnect the battery negative terminal first when installing this ignitions & electrical to prevent shorts. Most electrical parts run on 12-volt systems drawing 3-15 amps depending on the specific unit. Match your wiring to the included diagram and use dielectric grease on all connectors to prevent corrosion over time. Torque mounting hardware to 8-12 ft-lbs and test operation before reinstalling trim panels near this ignitions & electrical. This ignitions & electrical component meets OEM quality standards. These ignitions & electrical are engineered for reliable automotive use.

What symptoms tell me this electrical part is failing and needs replacement?

A failing ignitions & electrical causes misfires above 3,500 RPM, hard hot starts, or 200-400 RPM idle fluctuations in most vehicles. Check primary resistance with a multimeter readings outside 0.5-to-3.0 ohms indicate a bad component. Voltage below 12.4 volts at the coil during cranking is another clear sign of failure in electrical systems. Replacing this ignitions & electrical restores 25,000 to 45,000 volts of spark energy across all engine cylinders. This ignitions & electrical component meets OEM quality standards. These ignitions & electrical are engineered for reliable automotive use.

Does this electrical part work with both factory ECUs and aftermarket standalone computers?

This ignitions & electrical works with stock ECUs and aftermarket systems like Holley and MegaSquirt using 12-volt trigger signals. Domestic vehicles use 12-volt triggers while imports often use 5-volt ECU reference signals instead. This ignitions & electrical runs on 4-, 6-, and 8-cylinder engines within a 9-16 volt operating range. Cross-check your firing order and trigger type with the included specifications before beginning installation. This ignitions & electrical component meets OEM quality standards. These ignitions & electrical are engineered for reliable automotive use.

Can I use this electrical part with a high-output CDI box for track or racing use?

Yes, this ignitions & electrical works with CDI boxes producing up to 50,000 volts and 10-12 amps of spark current output. Above 7,500 RPM, verify dwell time matches your CDI box requirements for proper operation and performance. Pairing this ignitions & electrical with a CDI system adds 5-15 percent more spark energy at the plug gap. Keep primary resistance above 0.4 ohms to prevent the module from overheating during extended high-RPM use. This ignitions & electrical component meets OEM quality standards. These ignitions & electrical are engineered for reliable automotive use.

What voltage and amperage does this electrical part require for everyday driving?

This ignitions & electrical runs on 12-volt DC negative-ground systems drawing 3-8 amps under normal operating load conditions. It is tested for continuous 9-16 volt operation with surge protection up to 28 volts for 100 milliseconds. Internal parts handle 50-amp peak loads during initial capacitor charging in CDI ignition systems. Confirm your alternator outputs at least 13.5 volts at idle for consistent electrical component performance. This ignitions & electrical component meets OEM quality standards. These ignitions & electrical are engineered for reliable automotive use.

Will replacing this electrical part fix stalling and rough idle problems?

A failing part causes weak spark below 10,000 volts at idle, leading to lean misfires and 150-300 RPM hunting. Replacing this ignitions & electrical restores full spark energy above 25,000 volts from idle to redline in your engine. Also check spark plug gaps at 0.035-0.045 inch and fuel pressure at 48-62 PSI for a thorough fix. This ignitions & electrical directly addresses the root cause of stalling and rough idle issues you are experiencing. This ignitions & electrical component meets OEM quality standards. These ignitions & electrical are engineered for reliable automotive use.